Solution to eliminate error on Kyocera-Mita printers

Here is list of most comment error on the Kyocera-Mita printers and how to eliminate them.

The Kyocera-Mita printers were normally created for office use, they are very durable and efficient printers working with toners cartridge.

In this post, we are going to give you a list of most error appearing to this printer and how to eliminate them. If you are not able to eliminate the error on your own, please seek help by contacting the Kyocera-Mita support.

List of most common error code

Code	Meaning	Possible solution
A2	Overheating fuser	Adjust the fuser temperature.
A6	Fuser/cartridge does not rotate at the correct speed	Restart the printer. If the error persists, please contact technical support.
A7	Power supply fan is not rotating at the correct speed	Restart the printer. If the error persists, please contact technical support.
A8	Ozone fax that does not rotate at the right speed	Restart the printer. If the error persists, please contact technical support.
A9	Roll Multipurpose has an error	Clean the rollers.
B7	Transfer Roller is not reset properly after completion of work	Restart the printer. If the error persists, please contact technical support.
C1	Error communicating with the duplex unit	Restart the printer. If the error persists, please contact technical support.
C3	Motor duplex feed is not working properly	Restart the printer. If the error persists, please contact technical support.
E0	Communication error	Make sure all cables are plugged Restart the printer. If the error persists, please contact technical support.
E2	Scanner Motor not working properly	Restart the printer. If the error persists, please contact technical support.
E8	Fuser needs to be replaced	Please contact support for help with replacing the fuser.
E9	Cartridge engine is not working properly	Kyocera-Mita Remove the toner cartridge and reboot. Reinstall the cartridge.
C037	Microcomputer, ironing motor or main board does not work properly	Please contact technical support.
C640	Hard disk space can not be accessed	Make sure the hard drive is locked in place. Restart the printer.
C10	Exposure lamp does not work properly	Use the reference manual to locate the lamp and make sure it is connected. If the error persists, please contact technical support.
C210	Motor carrier Paper does not work properly	Remove the jammed paper.
C230 o C2500	Paper feed motor not working properly	Remove the jammed paper.
C7300	Cartridge to be read as the vacuum level, the toner not determined	Remove the cartridge and run a cold start. You can also shake the cartridge to redistribute the remaining toner. If the error persists, replace the cartridge.
C7800	Humidity sensor board does not work properly	Replace the board of moisture or contact technical support sensor.
C8140	Malfunction of the main paper tray - could be sensor or engine	Remove the tray to remove dirt and dust from the sensor and rollers. Reinstall the correct tray and try printing again.
C91	Wireless network printer does not work properly	Make sure all cables are properly connected.
E07	Media type and tray are not in line	Use a different paper tray, change the paper type, or change the paper settings.
E70	Previous task was not completed	Cancel the incomplete task or delete the print queue.
E90	Memory full - unable to complete the task	You can clear the memory to reset the printer or break the task up into multiple jobs. Another option is to upgrade the printer memory.
OP1 OP5	A drawer or cover is open	Close all drawers and tapas.
U00602	Paper Jam	Remove the paper jam.
U00603	The document does not feed correctly	Clean the rollers and use the alignment tabs on the paper tray toward the center of the paper.
U00614	Paper is almost out	Load more paper in the tray.
U00615	Paper is out	Load more paper in the tray.

If you have any questions you can contact us by leaving a comment in the section below this post, you can also visit the official manufacturer website or contact their support. This publication was translated and adapted by  +José Altagracia Paredes and was originally created by Greg Gladman.