Learn here how install the system continuous ink, to HP Deskjet 1000 printer in home.
As we know these printers have given much to talk about, but actually the problem has been cartridges for this printer, we made a post regarding the true secret of cartridges HP 122 both black as the tricolor, and we raised the reset of these cartridges, as we always say a good printer makes the ink cartridges, and this is a delicate printer Keyboard so to speak be careful and follow the procedure to exactly for the installation of the ink comes out right and not to ruin time and a lot of ink.
Anyway if it does not work you can choose to refill the ink cartridges both the cartridge 122 black and refill the ink cartridge HP 122 tricolor.
You need to have some instruments before beginning the installation of continuous ink system, most importantly in this case the continuous ink system with all its components, for this printer you can use an ink system that we can get at any filled or computers store, it is the same as used for installation on the Canon and the same water-based ink printers.
It is recommended to have a place with plenty of space, which is not a problem that ink stain, or a flat surface that can be cleaned easily, tools to cut any excess amount of hoses system.
1. The first thing you do is to place the ink in the ink tanks put them in consecutive locations depending on the place that corresponds to the cartridges, place these the same as going into the printer and replace the hose with the movement of cartridges only contacts the corner where cartridges do not rest or rather where it is not the cartridge cleaner.
As you can see in the picture above on the side where the ink system hoses accumulate, it's just where it is not the system that cleans the cartridges.
You need to put some clips to hold the cartridge at the top as shown in the picture. Unlike other HP printers use a carriage that holds the cartridges at a considerable height, so we will need to position hoses from continuous ink system as seen in the image with the help of the clips that hold the hose. See image below.
We cannot forget the ink cartridges, as these will have to put your elbows on your system before putting the hoses, when we have the elbows positioned correctly and without air leaks then do what is the cartridge bleeding _ to leave these connected without air leak and ink at rest.
Bleeding a cartridge is when we put the hose near either the hole in the cartridge or in this case the elbow ink system when the hose is close but not connected then supply air to the ink tanks, put the air just where the ink tanks take in air and when it comes to ink cartridges connect it and stop supplying air to ink tank.
Remember to seal the orifices _ 122, preferably using a heat gun silicone for this function. After you remove the system configuration ink on the right side of the printer by placing a hose clips to hold the ink system. see image below...
Always remember not to let the ink system runs until the end, if a hose system one day take some air then bleed as we have shown above, if you do not understand a step in this procedure type a Comment this post.
Anyway if it does not work you can choose to refill the ink cartridges both the cartridge 122 black and refill the ink cartridge HP 122 tricolor.
You need to have some instruments before beginning the installation of continuous ink system, most importantly in this case the continuous ink system with all its components, for this printer you can use an ink system that we can get at any filled or computers store, it is the same as used for installation on the Canon and the same water-based ink printers.
It is recommended to have a place with plenty of space, which is not a problem that ink stain, or a flat surface that can be cleaned easily, tools to cut any excess amount of hoses system.
1. The first thing you do is to place the ink in the ink tanks put them in consecutive locations depending on the place that corresponds to the cartridges, place these the same as going into the printer and replace the hose with the movement of cartridges only contacts the corner where cartridges do not rest or rather where it is not the cartridge cleaner.
 |
| position hoses ink |
You need to put some clips to hold the cartridge at the top as shown in the picture. Unlike other HP printers use a carriage that holds the cartridges at a considerable height, so we will need to position hoses from continuous ink system as seen in the image with the help of the clips that hold the hose. See image below.
 |
| position to hold system with clips |
Bleeding a cartridge is when we put the hose near either the hole in the cartridge or in this case the elbow ink system when the hose is close but not connected then supply air to the ink tanks, put the air just where the ink tanks take in air and when it comes to ink cartridges connect it and stop supplying air to ink tank.
Remember to seal the orifices _ 122, preferably using a heat gun silicone for this function. After you remove the system configuration ink on the right side of the printer by placing a hose clips to hold the ink system. see image below...
 |
| system position |
COMMENTS