When you printer, get the pages spot you need clean the toner cilindre, and other steps here.
The Laser printers are those that can be used for the hard work they need, usually they work well and give us a superior print quality and very durable.
These printers work with a toner which contains a powder that is reflected in the pages when heated with a heat fuser.
It is possible that one day either because we fill the toner or because we have a lot to not use the printer some spots throughout the site begin to appear, these seem drops or black spots that protrude on pages removing the clear quality of our work.
These printers work with a toner which contains a powder that is reflected in the pages when heated with a heat fuser.
It is possible that one day either because we fill the toner or because we have a lot to not use the printer some spots throughout the site begin to appear, these seem drops or black spots that protrude on pages removing the clear quality of our work.
AaBbCc |
The cause depends on where you find spots, always the direct cause is due to problems with the toner there is a remote possibility that it is caused by the printer but the possibility exists then present a set of possible solutions that can be applied to obtain a solution.
If you do not have much toner usage, we're talking about 100 pages follow the steps below.
If you have completed the re-manufactured toner or there is a possibility that the toner it no longer misplaced parts inside the toner recommend that you contact the company that has filled the toner.
If you purchased an original new toner contact who sold the toner as long the toner have a full warranty and it is almost never expires, you have to spend many times, tell the truth to the dealer to know what case is presented, have hanging that these should not get wet or leave it in a place with high temperature.
Do the same procedure if you have bought a new compatible toner. We now present a set of possible solutions that would help us solve any spilled ink or problems with the cylinder having the toner.
To begin review the feed roller of our printer
This is who brings the pages to print channels, the taking of the feed tray pages so that this process begins printing.
There is the possibility that sometimes this gets dirty with toner powder, or just waste which would cause a stain, only one central spot on the top of the page.
To remove this stain we will have to clean the feed roller, this'll clean it with alcohol and some clean cloth, and we can also use napkin or any other material that serves to clean.
Before cleaning the feed roller printer we have to switch off the printer power cord electricity, we can disconnect directly from the printer or the power connector cord into the wall, with this we seek to eliminate the possibility of receive damage with electricity.
This part is where to put the blank pages, it is usually in the bottom of the printer, always place where pages. It is inside an iron pipe and looks like this. view image...
With this we reduce some stains on the pages but not all printers have this feature.
We'll have to go to the printer properties and look at the options at the top where it says device configuration and then print a cleaning page.
This page will slowly and may take approximately 2 to 3 minutes out completely. You can also perform a cleaning process from the printer panel on top of the computer, surf the tools and settings of this, it will depend greatly on where you are, each printer model and brand have a different menu.
So we must remove the printer toner and a wet washcloth water to clean the area where the toner inside the printer is, we have to put toner in a place where it is not exposed to sunlight and we need to clean the printer disconnected from electricity.
Make a cleaning slowly and carefully, do not clean the black sponge inside the printer, this may damage the printer. view image of the area we have to clean...
If none of these processes have worked to pass a complete clean toner, and for this we need a little more knowledge of printers and management of repair, if the toner is about to spend, this it may be filled with ink tanks behind the blade toner.
We recommend rolling the cylinder toner, does it slowly and carefully to avoid damage to the cylinder, with it we seek to clean the waste of toner powder.
If we disassemble the toner will see that there is a cleaning blade like the picture above, this we have to clean it, and to do this we need to remove it and remove all dust in the back of the blade.
It is recommended to use masks to prevent the penetration of dust into our bodies, bare hands to avoid any allergies that cause this powder. We must review the cylinder toner for dirty or has pieces due to shock or zest, if so we will have to be replaced.
After the whole process is done print a test to see how the result is, if it is not functioning you have to purchase of a new toner.
how to clean the roller |
insert your hand and wipe gently |
To clean stains from the system pages
In case of seeing that the pages are coming out with slight traces apparently caused by toner tour, we will see in the need to use the printer software to perform a cleaning directly from the program.With this we reduce some stains on the pages but not all printers have this feature.
We'll have to go to the printer properties and look at the options at the top where it says device configuration and then print a cleaning page.
This page will slowly and may take approximately 2 to 3 minutes out completely. You can also perform a cleaning process from the printer panel on top of the computer, surf the tools and settings of this, it will depend greatly on where you are, each printer model and brand have a different menu.
Clean inside the printer, where the toner is
If you have used a toner long time, or if we have filled this and is pouring dust, it is advisable to clean the area where the toner is located.remove laser printer toner |
Make a cleaning slowly and carefully, do not clean the black sponge inside the printer, this may damage the printer. view image of the area we have to clean...
area to clean laser printers |
We recommend rolling the cylinder toner, does it slowly and carefully to avoid damage to the cylinder, with it we seek to clean the waste of toner powder.
cleaning blade |
It is recommended to use masks to prevent the penetration of dust into our bodies, bare hands to avoid any allergies that cause this powder. We must review the cylinder toner for dirty or has pieces due to shock or zest, if so we will have to be replaced.
After the whole process is done print a test to see how the result is, if it is not functioning you have to purchase of a new toner.
COMMENTS